Volume 3, Issue 6, December 2017, Page: 56-62
Modeling and Optimization of Carbon Steel AISI 1045 Surface Roughness in CNC Turning Based on Response Surface Methodology and Heuristic Optimization Algorithms
Vijay Nagandran, Department of Mechanical Engineering, Universiti Tenaga Nasional, Selangor, Malaysia
Tiagrajah V. Janahiraman, Department of Electronics and Communication Engineering, Universiti Tenaga Nasional, Selangor, Malaysia
Nooraziah Ahmad, Faculty of Creative Technology and Heritage, Universiti Malaysia Kelantan, Kelantan, Malaysia
Received: Oct. 30, 2017;       Accepted: Nov. 22, 2017;       Published: Jan. 11, 2018
DOI: 10.11648/j.ajnna.20170306.11      View  1524      Downloads  66
Abstract
Surface roughness or surface quality is considered to be one of the most crucial requirement of a machined part since it directly influences the mechanical properties of the part. However, the traditional method of choosing cutting parameters’ values to obtain a good surface finish has its own disadvantages. Therefore, an experimental study has been conducted to develop a suitable mathematical model and pair it with an optimization technique that able to produce low surface roughness of carbon steel AISI 1045. Response surface methodology (RSM) is used to develop the mathematical model whereas three types of heuristic optimization methods namely Genetics Algorithm (GA), Particle Swarm Optimization (PSO) and Simulated Annealing (SA) employed to optimize the model and find the optimal cutting parameters’ values. A brief comparison of the three optimization methods has been made to study their performance to the developed model. Experimental results indicate that the proposed modeling technique and PSO are quite efficient in determining optimal cutting parameters for CNC turning of carbon steel AISI 1045.
Keywords
Carbon Steel AISI 1045, Genetic Algorithm, Particle Swarm Optimization, Response Surface Methodology, Simulated Annealing, Surface Roughness
To cite this article
Vijay Nagandran, Tiagrajah V. Janahiraman, Nooraziah Ahmad, Modeling and Optimization of Carbon Steel AISI 1045 Surface Roughness in CNC Turning Based on Response Surface Methodology and Heuristic Optimization Algorithms, American Journal of Neural Networks and Applications. Vol. 3, No. 6, 2017, pp. 56-62. doi: 10.11648/j.ajnna.20170306.11
Copyright
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
Makadia, A. J., and Nanavati, J. I., “Optimization of Machining Parameters for Turning Operations Based on Response Surface Methodology”, Measurement, Vol. 46, No. 4, (2012), 1521-1529.
[2]
Rao, V., “Advanced Modeling and Optimization of manufacturing processes”, London, Springer, (2011).
[3]
Sandor, B., and Bel., K., “Lean Production Planning for 5 Axes CNC Driven Milling Machine”, Machine Learning Research, Vol.2, No.2, (2017), 66-72.
[4]
Yang, X. S., “Engineering Optimization: An Introduction with Metaheuristic Applications”, New York, John Wiley and Sons Inc, (2010).
[5]
Gao, W. F., and Liu, S. Y., “A Modified Artificial Bee Colony”, Computers & Operations Research, Vol. 39, No. 2, (2012), 687-697.
[6]
Haupt, R. L., and Koehler, A. B., “Practical Genetic Algorithms”, New York, John Wiley and Sons Inc, (1998).
[7]
Chandrasekaran, K., Marimuthu, P., and Raja, K., “Prediction Model for CNC Turning on AISI316 with Single and Multilayered Cutting Tool Using Box Behnken Design”, International Journal of Engineering, Transactions A: Basics, Vol. 26, No. 4, (2013), 401-410.
[8]
Azadi Moghaddam, M., and Kolahan, F., “Modeling and Optimization of Surface Roughness of AISI2312 Hot Worked Steel in EDM based on Mathematical Modeling and Genetic Algorithm”, International Journal of Engineering, Transactions C: Aspects, Vol. 27, No. 3, (2014), 417-424.
[9]
Alimirzaloo, V., Modanloo, V., and Babazadeh Asbagh, E., “Experimental Investigation of the Effect of Process Parameters on the Surface Roughness in Finishing Process of Chrome Coated Printing Cylinders”, International Journal of Engineering, Transactions C: Aspects, Vol. 29, No. 12, (2016), 1775-1782.
[10]
Kalidass, S., and Mathavaraj Ravikumar, T., “Cutting Force Prediction in End Milling Process of AISI 304 Steel Using Solid Carbide Tools”, International Journal of Engineering, Transactions A: Basics, Vol. 28, No. 7, (2015), 1074-1081.
[11]
Shivade, A. S., Bhagat, S., Jagdale, S., Nikam, A., and Londhe, P., “Optimization of Machining Parameters for Turning Using Taguchi Approach”, International Journal of Recent Technology and Engineering, Vol. 3, No. 1, (2014), 145-149.
[12]
Khamaruzaman, Y., Nuraddeen, B., Muhammad, M., and Mohamed, I., “Linear Kernel Support Vector Machines for Modeling Pore-Water Pressure Responses”, Journal of Engineering Science and Technology, Vol.12, No.8, (2017), 2202-2212.
[13]
Shukurillo, U., “Optimization of the Launching Process in the Electric Drive with the Help of Genetic Algorithm”, Machine Learning Research, Vol.2, No.2, (2017), 61-65.
[14]
Michalewicz, Z., “Genetics Algorithm + Data Structures = Evolution Programs (3rd ed.)”, New York, Springer, (1996).
[15]
Eberhart, R. C., and Kennedy, J., “A New Optimizer Using Particles Swarm Theory” in 6th International Symposium on Micro Machine and Human Science, Nagoya, Japan, 39-43. (1995).
[16]
Eberhart, R. C., and Kennedy, J., “Particle swarm Optimization" in IEEE International Conference on Neural Network, Perth, Australia, 1942-1948, (1995).
[17]
Bidya Prakash, M., and Shatendra, S., “A Review on Application of Bio-Geography Based Algorithm and Other Optimization Techniques, International Journal of Management, Information, Technology and Engineering, Vol. 3, No. 6, (2015), 19-28.
[18]
Majhi, B. P., and Sahu, S., “A Review on Application of Bio-geography Based Algorithm and Other Optimization Techniques”, International Journal of Management, Information Technology and Engineering, Vol. 3, No. 6, (2015), 19-28.
[19]
Balram, S., “Study of Simulated Annealing Based Algorithms for Multiobjective Optimization of a Constrained Problem”, Computers and Chemical Engineering, Vol. 28, No. 10, (2004), 1849-1871.
[20]
Nooraziah, A., and Tiagrajah, V. J., “A Study on Regression Model Using Response Surface Methodology”, Applied Mechanics and Materials, Vol. 66, No. 6, (2014), 235-239.
Browse journals by subject